Where can I find Fieldpoint 6.1
I recently upgraded to LabView 2013 and, since then, I can no longer get my software to communicate with my FieldPoint hardware. I am using FieldPoint driver version 6.0.11. I've been poking around...
View ArticleFI-AO-200 and FI_AI-110
Hi, I have an alicat mass flow controller (MCR). I need to wire for both input and output signal. I have an FI-AI-110 to read in 0-5 V signal and an FI-AO-200 to sent out 4-20mA signal. The alicat...
View ArticlecFP-PWM-520 ch0 was working then stop can not get any PWM signal
I was using the cFP-PWM-520 to control a H-Bridge(with higher current capability). I was getting eraric output of the H-Bridge, while checking I found the +24VDC input into H-Bridge loose an proceded...
View ArticleFP1601 connectivity issue, error message: 33162
Hi, I am currently having problem connecting to my FP1601 ethernet interface from the host computer. Here is a little bit of background: There were two ethernet cards on my host computer and the cross...
View ArticleWhat is the function of the FP Write VI?
Hello, I'm currently a beginner getting familiar with LabVIEW. I'm trying to learn to utilize FieldPoint hardware and I came across the FP Write VI. I'm wondering what exactly is the function of this...
View Articlewhat is the last version of labview to support classic FieldPoint?
what's the last version of labview to support classic FieldPoint?
View ArticleFP TC 120 Output
Hi everyone, I will be using the FP TC 120 module to measure several temperatures using thermocouples. My question is that if I use FP Read to read the output from FieldPoint IO Point In which...
View ArticleWhat's the maximum digital I/O frequency for the NI LabVIEW RIO Evaluation Kit ?
Hi! I'm trying to analyze some sort of sine signal at the frequency of about 3 MHz. Because the analysis should be very precise and fast (about 10 samples per period), I'm needing the maximum digital...
View ArticleCan't find subFieldPoint.vi in Labview2013
I have updated my computer to LabVIEW2013 and I need to move a FieldPoint application over to Windows 7. My old vi says the subFieldPoint vi are no good. OK, so where are the new ones? I updated...
View ArticlecFP IP Address changes when unplugged
HI, I have a cFP 2200 with 1 AI-110 input module, 1 AO-200 output module, and 1 RLY-423 Relay module. Every time I unplug the power to the cFP system and then plug it back in the IP address changes. I...
View ArticleFieldPoint to 9-Pin D-Connector
Hi, I'm wondering if it is possible to use the FP-AI-112 input module to read from a digital power supply that displays flow rates. The manual for the power supply states that it has 9-Pin D-connector...
View ArticleRigol DG1062
I am using . I can’t get a Labview driver for this specific function generator. I try the DG4000. I gives me a signal error and can’t figure it out. Can you please suggest me how to get the Labview...
View ArticleFiieldPoint example fails to deploy
Hardware: FP-2015Software: Labview RT 8.2.1, FieldPoint 6.0.6f Software on FP-2015:FieldPoint 6.0.6 - Feb 2010DataSocket for LabVIEW Real-Time 4.4FieldPoint Drivers 6.0.6FieldPoint VI Manager...
View ArticlecFP Module ID over Modbus
I have a cFP-1804 base with several modules installed and I'd like to be able to identify which module is in a particualr slot. I'm using Modbus to do all my configuration and data collection. Is there...
View Articleerror writing to field point
I am trying to connect Field point FP-1001 by Ni PCI-485/2 multifuction adaptor . when i start the program by Ni scope i found " ERROR WRITING TO FIELD POINT". i have checekd the pci card and its...
View ArticleClik here to view.
FieldPoint cFP-1601 and MAX5.6 configuration
Dear All, I would like to share a way to configure the cFP-1601 Ethernet using the MAX 5.6 that doesn't anymore supports this device. The solution is an workaround on the compatibility problem for MAX...
View Articlecfp-ctr-500
Hi, I have recently upgraded a system from fieldpoint modules to compact fieldpoint.I have a cfp-ctr-500 module which I use to generate a pulse output, a terminal count attribute is used to program the...
View ArticleHow to read USER1 DIP-switch status of a cRIO chassis from FPGA?
How can I read the status of the DIP switches on a cRio chassis from the FPGA? I am working with a cRIO 9022.. My idea is to set the system into a "service" mode by setting the USER1 switch to ON and...
View ArticleClik here to view.
R.I.P. Compact FieldPoint
I knew our favourite automation controller, the cFP-2220, is set to be unavailable from 2016, but for some reason I still expected it to be programmable in LabVIEW 2014. As far as I can see the plug...
View Article