cfp 180x modbus
I am trying to communicate with the cfp1804 via modbus and am not receiving a response from the unit. I am able to establish a connection, but cannot receive any response from the slave. I am...
View Articlefieldpoint fp-2210 serial
I have a Compact Fieldpoint cPF-2210. On the base unit there are two RS-232 ports available. Is it possible to communicate to an external device over RS-232 with these ports? I installed NI-VISA Server...
View Articlecfp2200 backplane Question
I have a CFP-2200 which is configured with a CFP-AI-112 and CFP-CB-1 in the first 2 slots on the backplane next to the CFP-2200 CPU module. There are a couple of broken pins on the backplane connector...
View Articleconnector block availability
Hello, I have a cFP-1808, however am missiting the connector block pictured on page 13 of the cFP-1808 Quick Start Guide. Where can I aquire or buy one? Thanks,Dan
View Articlereading cFP-2100 with python
Hello,I have a NI cFP-2100 with ethernet connection, and I would like to read its measurementsfrom a python program. Is there a way to do this ? Thanks in advance, Stefano
View Articlefalla de comunicación serial con ejecutable
hola. tengo un ejecutable que mide 4 sensores de presion , su comunicacion es serial. el problema que tengo es que el ejecutable no responde igual si lo cargo en otro cpu, no lee los sensores, me dice...
View ArticleFieldpoint-2010 not found, some IP problem ?
Hello. I try little say what is what I know. I'm automation student in Finland and I should connect MetsoDNA PC-operator and Fieldpoint-2010 together. I'm doing my graduation work and I have big...
View ArticleNI 9214 FPGA I/O items missing (cRIO-9030 / NI 9144 combo)
I have a new cRIO-9030 and NI 9144 EtherCAT expansion chassis which I have configured and added to an existing LabVIEW project containing a cRIO-9012. When I searched for existing targets and devices,...
View ArticlecFP-2000 can't find modules on bank
Hello,I'm using this cFP-2000 for a while, and now I have another problem:The cFP-2000 cannot find any module connected to it, when I go to MAX and ask to find devices, all I got is the controller...
View ArticleTransitioning From Compact FieldPoint to CompactRIO
This is in regards to the White Paper with the same name as this Post Subject: http://www.ni.com/white-paper/52272/en/ I wanted to respond with feedback right on the White Paper, but it seems like that...
View ArticlecFP-2210 not detected in NI MAX
I just got one fresh unit of cFP-2210 controller, when the ethernet port connects to same network with my PC, the NI MAX in my PC cannot detect the cFP. Any advice on this scenario ? Thanks
View ArticleFP-2000 Error: Serial port receive buffer overflow
HelloI am trying to get an old system working, that was set up by someone else, and upon running our program we get the following error: Error 63 occured at TCP Open Connection in Host...
View ArticleCannot find dependent files subFieldPoint.llb and pid.llb for old LabVIEW...
I am trying to get an old LabVIEW program to work that originaly written in LabVIEW 2009 using the FieldPoint module. (thats all the information I have on the old program) I have installed LabVIEW...
View ArticleField Point FP-1000 communication issue - Device found but offline in MAX
Hello, I am trying to control several field point PLCs in a level tank. They are communicating through a FP-1000 module. I am able to add the devices through a configuration file in MAX. But there is...
View ArticleNeed to acquire DSC 7.1 for backup configuration
Hello, Is LabVIEW DSC 7.1 included in LabVIEW 7.1 Platform Addons? DM
View ArticleField point blinking signal
Hi, Can someone pls advise me , is there a way to program in block diagram if the blinking signal come from field point ?In the attached photo .. there is Green and Orange signal come from field...
View ArticlecFP-AIO-610 electrical isolation between input and output channels
Manual states "The input and output channels of the [c]FP-AIO-610 are not electrically isolated from each other". I assume this means that the commons on the input channels are connected and the...
View ArticleLV2010 and cFP-2120 and remote panel
I have a project in LV2010 for cFP-2220. When I convert the project for a cFP-2120, the remote panel doesn't work. When the browser goes to the IP address it defaults to 192.168.1.2/#Home.
View ArticleUSRP-2940R FPGA Customization
Hi, Is it possible to customize the FPGA of USRP-2940R? Can it be considered as an Ettus X310? Regards
View ArticlecFP-1804 get current time
Hi,I'm trying to squeeze the last bit of control loop speed out of the cFP-1804, and to do that I need to synchronize the control loop (running on PC) to the sampling of the slowest module in the...
View Article