Labview getting crashed
Hi,When I start LabVIEW, after few seconds it gets crashed. Any solution? Hardware - cFP-2110
View ArticleFP1601 not detected
MAX does not detect the FP-1601 unit.FP-1601 has been reset as the IP was unknown. The reset switch is returned to the OFF position. All switches are OFF.Status LED is blinking red at 1 blink per...
View ArticleSet voltage level of discrete output module
I have a couple of FP-DO-DC60. The limited documentation I've been able to find says their output voltage range is 3-60V but doesn't say how to set the voltage level. Does anyone know how to do this?
View ArticlecFP RS232 possbily not according to standard?
We are using a cFP 2220 as multipurpose controllers, and in some scenarios, we implement additional safety circuitry to protect the I/O ports against incorrect connections; typically power connected to...
View ArticleUpgrading from FieldPoint FP-1000, FP-RLY-420, and FP-DI-330
Hi, Looking to upgrade my modules without having to change anything else. We run Macs with LabVIEW, connected to the FP-1000 modules through an ethernet-to-GPIB converter, and then through a...
View ArticleRS232/RS485 Converter Circuit Receiving Problem
Hi, I'm trying to make an RS232/RS485 converter circuit. I used a circuit from http://airborn.com.au/layout/232cnv/232to485.html and i changed some components on that circuit. Then i established my...
View Articlebad quality received from network module FP-1600
Got FP-1600 on Lookout 6.7 running OK till few days ago when I got this message under alarms:< bad quality received from network module>What/how can I configure and save the configuration? In MAX...
View ArticleCan you connect a DB37 cable to a cfp-cb-1 connector block?
Hello All,I am looking at upgrading an existing compact field point unit to a cDAQ unit and I am figuring out a way to test the new system without having to unwire and re-wire all of the old compact...
View ArticleI have the labview 2014 and i can connect to the fp-1000 , but there is no...
I am new to using filedpoint, I have the labview 2014, i am using the temperature measurement example for the fp-tc-120, it will find the fp-tc-120 but when i run the programme im not getting and data...
View ArticleClik here to view.
ERROR 34200
I am still getting the error 34200, is this because I am using the evaluate fieldbus 4.1? or is there something else i need to do, I have attached a picture of what appears. Can anybody help me with...
View ArticleFP-TB-3 CJC calibration
The FP-TB-3 has a CJ imbeded into the TB. This is not calibrated separatly but is used in conjuction with FP-120. The FP-120 is calibrated for CJC but is never linked to the TB. There should be a...
View Articledriver fieldpoint 6.0.4
Dear NI community, I've a problem with my cFP 1804. I've installed LabView 2009 on Windows XP and the 6.0.10 version of Fieldpoint. I can import my Fieldpoint in LabView (previously configured in MAX),...
View ArticleCFP1804 with AIO 600
I have been trying to use a 1804 network module with a AIO-610, this has been working fine so far with firmware 6.08 (tried 6.05 but no improvement) I can write AO channels in max and via modbus...
View ArticlecFP disconnected in MAX but responds to UDP broadcasts
Hey guys, I have 4 cFP controllers in the field monitoring a whole bunch of sensors. Each sensor has it's own calibration, and so I built an OO hierarchy based on Dynamic Dispatch to handle it. Now...
View ArticleLooking for an FP-RLY-420 to buy
I have a FieldPoint based test system that has a bad channel in a FP-RLY-420 module. Not sure if it is a relay coil or drive circuit issue. I will try to repair later. I need to get this production...
View Articleusers login and MAX configuration
I have searched the site for 3 days and finally found a post titled; "IAK user login and MAX configuration" on 4/21/2009 that asked about the same issue I am having. I am wondering if there is anything...
View ArticleClik here to view.
issues with cfp AIO 600 output
Hi, I am trying to get cfp AIO 600 to output current, for this I am using the sample VI for the cfp AIO 600. I cannot get current on the output and I have trouble troubleshooting the issue. 1) How...
View ArticleGetting an old fp-1000 back into action
hello everyone,Our situation goes as follows: we have an old fp-1000 device attached to three fp-ai-110 along with some temperature sensors. The overall system, as far as I know, was running smoothly...
View ArticleWhy cant MAX see my cFP1808's?
I have just purchased two cFP1808 chassis but when I try to configure them using MAX, they do not appear under Remote Sysems. I have a direct ethernet connection to the devices using a CAT5 XOVER cable...
View Articleask for a help in a mini project:text to speech
I've been working on a project that should convert a text to speech in arabic language . This program consist to convert each letter from the file(.py type) to a number (correspond unicode) in1D array...
View Article